Settings Tab

The Settings tab contains configuration settings for the selected device. Options vary by device and by queue.

Settings tab

General

Name Enter a queue name.
Print mode

Select a print mode from the drop-down list.

bonus-docFiltering Print Modes in a Queue

Opens the Print Mode Selection dialog. Use the table in the following link for configuration options: Print Mode Manager
Choose color

Select a substrate color using the sliders. Select from RGB or CMYK.

Note: The next imported job displays the color change.

Change image Set a queue image (useful for setting up and easily identifying a recurring output).
Remove image Remove the queue image.
Image tooltip Enter a tooltip for the queue image.
Create print mode Create a print mode based on the current settings.
Defaults
OK
Cancel
Hot Folders
Enable queue hot folder

A hot folder is a specific directory the queue monitors for new design files. When files are added to the hot folder, they are automatically detected and added to the queue as print jobs.

Browse for a folder to send jobs, and select Delete file after processed by queue if desired.

Note: To edit this location, click the ellipsis button on the right.

Enable template hot folders

Browse and create an empty folder, and select Delete file after processed by queue if desired. Select Match jobs on template by file name to group the jobs on the same template.
Note: Template folders are automatically created for jobs.

Using Hot Folders

Sending to a Hot Folder from a Mac

Media Setup

Type Select a media type from the drop-down list.
Name

Select media from the drop-down list. Use the () button to launch the Print Media Manager dialog (see Print Media Manager).

Note: If you select <Add New Media>, the Template Setup dialog is launched (see Template Setup dialog). Depending on the media, you may see the Media Setup dialog or the Template Setup dialog. If the Media Setup dialog appears:

  • Enter a name, size, and margins.
Margins
Cutter page size Select to limit the media to the maximum cutter dimensions, use the arrows to set the cutter page width and height, and click From driver to get the page size from the driver (the change is automatically applied).
Cut template slots using process Select to enable, then use the drop-down list to select a process, and click Create new cut process to launch the Cut Process Management dialog.

Select a cutter, enter notes, select the process, enter notes, save, and delete.

Select the check box next to each option to enable it and configure the settings.

Click Save and then Close.

Clip job on import using template slot cut pattern

Using template media, select to apply a slot cut pattern on import.

Clip Using Slot Cut Pattern

Layout Manager

Layout jobs on page as they arrive Select to lay jobs out on the page as they arrive. If this option is disabled, jobs are sent to the reserve list.
Rotate job on import

Select to rotate jobs when they are imported. Set a degree of rotation.

Note: Not available with Template media configured.

Mirror jobs on import

Select to mirror jobs on import horizontally (reverse the jobs, useful for vinyl application).

Note: If you have also set rotation, the image is mirrored, then rotated (useful for sublimation/laser on transfer media).

Invert job on import

Select to invert job color on import (invert color or white/black values, like a photographic negative).

Note: Does not work on PDF.

Preview multiple page jobs as an overlap (all pages overlay)

Select to display jobs that have more than one page as an overlay (only the first page will be visible).

bonus-docPage Order when Sending Jobs to the Queue

Duplex

Select to print on both sides of a page. Click the ellipsis button for duplex options.

Select from Basic, Template, or Book.

If Basic is selected, you can rotate even pages by 180 degrees.

If Template or Book is selected, select or create a template for odd pages, and another one for even pages.

Optionally, select Duplex PDF files on import.

To apply duplexing, right-click the job or use the Jobs menu.

Template Setup dialog

Crop job to cut bounds if cut data exists Select to crop the job to the cut bounds (if the data exists).
Pause between copies Select to pause between each copy.
Position on page

Click on the image to select a position on the page from the 9x9 square that appears.

Note: Available in Roll Media and Fixed Sheet Media.

Layout jobs right to left

Note: Only applicable to roll media.

Confidence strip

Select one or more of the options:

  • Left
  • Right
  • Top

Select Add Lead-in to add a lead-in to the confidence strip.

Layout mode Use the drop-down to select Manual (add new jobs without conserving media), Auto Page (add a page break as each job is received), or Auto Nest (automatically reposition jobs to conserve media).
Remove excess white space from output Select to remove excess white space trailing the print job.
On job import

Select one of the following:

  • Leave as is (do not change on import)
  • Auto tile (when selected, the Options button is available)
    • Click Options.
      The Tile Overlap Options dialog appears.
    • Select the overlap mode and edges, then set values for X and Y.
  • Scale: if larger
  • Scale always (to fit media)
Close page... Select to close the page [on given action].
Allow job rotations when nesting Select to enable rotation of jobs for automatic best fit while nesting.
Space between jobs Use the arrows to set the space between each job.
Show Import Template Job dialog Select to show the Import Template Job dialog when importing every job.
Automatically close template when all slots filled
Remove white space from bottom  
Remove white space from right
Output scheduling Use the drop-down list for print, cut, and print and cut jobs to schedule output for closed jobs/pages.
Printer Status
You can schedule device maintenance.
Note: Not available for all devices.

Job Reserve

Enable job reserve
Save spool file on job reserve
Auto clean reserve Select to automatically clean the job reserve, and use the arrows to configure the date interval.
Delete reserved spool files

Print Labels

Enable print labels

Select annotations to print alongside production markup. Select to print labels per copy or per job.

Add barcode and select type and position.

Select Do not apply processing options to disable white underbase generation.

Confidence strip

Select one or more of the options:

  • Left
  • Right
  • Top

Select Add Lead-in to add a lead-in to the confidence strip.

Set width and height.

Set an X offset.

Select Do not apply processing options to disable white underbase generation.

Production Markup
Select system

Select a production markup system for output to ensure proper alignment.

Note: If Saga/Secabo cutter selected, stop the Cut Spooler before proceeding.

There are three modes:

  • Auto-trigger: Feed paper, machine reads barcode, one page at a time (best for unsupervised output).
  • No barcodes: Feed paper, machine reads registration marks, click Cut, papers feeds, aligns, and cuts.
  • No marks: Click Cut, machine calculates paper position.

Weed Borders

Graphtec Barcode Support

Select mode

Set the markup application per job or per page.

Note: Not applicable to weed border marks.

Select mark color Set a color by clicking Choose color.
Markup system settings

Set width, height, stroke, offset, type, thickness, number of marks, distance, etc. When finished, click OK unless adding multiple systems.

Cut path shift X, Y

Shift cut path on X or Y axis.

Note: If top left is aligned, shift not required.

Cut path stretch X, Y

Stretch cut path on X or Y axis.

Note: If bottom right is aligned, stretch not required.

Reset mark detection origin Click to reset origin and dialog. On auto-trigger, set origin.
Settings

Select to add start and end marks, and to cut from the end of the roll, as well as the offset.

Note: For cutter, offset is based off the marks (cut offset from the calculated cut).

Margins
Padding
Add markup system

Add a markup system based on selected values.

Note: Only applicable if multiple systems are added. Click Add markup system when adding a second markup system.

Note: If Saga cutter selected, margins must be equal for reverse barcode. Adjust in this tab.

Add multiple systems

Select to enable multiple production markup systems. When this is enabled, a list with controls appears on the right above the preview.

Note: If you have added multiple markup systems, select them to make changes.

Enable barcode for Find Job Select to enable the barcode for Find Job (see Finding Jobs).

PDF Export

Use the following path Set a location to save PDFs.
Include the cut data within the PDF document
Output overlaid pages as single page documents

Embedded Cut Path Options

Note: Only applicable if the file includes a cut path or one has been assigned in the queue.

Remove cut data from published PDF Select to remove cut data in the file.
Clip object using the cut path Select to clip the object using the cut path set in the file.
Output the cut path as an independent object Select to create an independent object from the cut path.
Bitmap Compression
None Select bitmap compression format.
Deflate
JPEG
Max compression If JPEG is selected, select a quality setting.
Best quality
Use these settings for all PDF operations (Extend Production Area, Spin/Rotate and Clip)  
Ignore overlap and output as multi-page PDF  
Include image ICC in the published PDF  

Shape Nesting Setup

Allow job rotation when shape nesting

Enable jobs to rotate when shape nesting to save media during output.

Specify possible rotation (in degrees)

Specify the possible rotations allowed when nesting. A lower rotation results in a slower calculation.

  • 90° rotation = 4 angles per shape
  • 45° rotation = 8 angles per shape
  • 30° rotation = 12 angles per shape
  • 15° rotation = 24 angles per shape
  • 10° rotation = 36 angles per shape
  • 5° rotation = 72 angles per shape
Space between objects Set the amount of space between nested objects, ensuring enough room for production.
Delete original jobs after nesting Select to remove all original jobs from the queue, and keep the new, nested job.
Grommet Setup
Print grommet marks Select to print grommet marks, then set the size and choose a color.
Inverse background color Select for the grommet color to be the inverse of the background color.
Grommet spacing

Select by distance or by number:

  • Select top, bottom, left, and/or right, set the maximum distance and offset. Select All same to use the same values for each grommet.
Place grommets on each tile

General

Name Enter a queue name.
Choose color Select a substrate color using the sliders. Select from RGB or CMYK.
OK
Cancel

Job Reserve

Enable job reserve
Auto clean reserve Select to automatically clean the job reserve, and use the arrows to configure the date interval.